This automatic optical fiber tensile testing system is made for operator skill independent use within production and lab settings. Two basic design configurations allow the consumer to select between a set up for regular linear proof testing along with extra mandrels for rotary higher strength testing.

The linear edition is designed for creation evidence testing with causes up to 22 N. Motorized clamps with very carefully designed rubber inserts ensure that the FTTH Cable Production Line is not damaged in the screening procedure whilst simultaneously getting rid of the need for an outside air provide. Levels of pulling force, pulling velocity and hold time are automated and easily offered to the owner from the built in LCD touch-screen manage. Information from assessments can be saved and reached using the USB port or Ethernet user interface.

Mandrels of the same design as with NYFORS’ optical fiber recoaters can be mounted on the evidence tester within the rotary high power settings. The fiber is covered around the two mandrels which support it having a unique clamping mechanism. By doing this higher lots can be applied on the fiber, enabling breaking power assessments under managed conditions.

Adjustable clamp placement facilitates testing using the highest force amounts as well as testing of short fiber measures. The lightweight and light weight design helps make the tool simple to maneuver inside a laboratory environment and also to incorporate in a production work bench where space reaches a premium. The machine is actually a compact and lightweight tool suitable for screening the effectiveness of optical fibers up to 30 N. The machine is developed to meet all sorts of applications in which a power check must be performed.

The machine is designed with all the consumer in mind. The fiber is readily placed in the guided linear clamps, as well as the screening starts instantly using a “One Touch” go button. The built-in microprocessor controls all the essential parameters including pulling force, pulling speed and hold time. This enables for a totally controlled test each and every time.

The machine can be linked to an outside Computer, which allows access to all automated guidelines and settings. The machine is tailored to face-on your own use or even to the incorporation into different subsystems. The machine comes with an extensive ability of logging and saving information including pulling force, tugging velocity and Secondary Coating Line as well as other parameters.

Two recoat injector designs can be purchased. The PTR307 uses an automated water pump to inject the recoat material. The volume of materials dispensed by the automatic injector is controlled by hand using the top-mounted “Inject” switch or programmed in to the machine utilizing the tablet controller. The PTR307B comes with a handbook recoat injection system that will require the user to personally dispense the recoat material to the mold cavity; a substitute injector for the PTR307B recoater is available listed below. Make sure you note that the automatic injector is simply compatible with high-directory recoat materials, as the manual injector is compatible with both low- and- directory recoat materials; both of them are marketed individually below. Please contact Technology Assistance for more information.

he handbook injector can be installed to Fiber Coloring Machine using the 4-40 anchoring screws in the recoater real estate (see picture for the right). Utilize a 3/32″ hex key to safe the injector prior to use. To connect the PTRRRM for the recoater mold, tighten up the connector at the conclusion of the eco-friendly plastic material tubes, then release by way of a 1/4 turn to enable rotation.

The injector is equipped with a distribution valve as well as 2-position selection lever for directing the flow of recoat materials. A knurled dispensing screw with the inner plunger behaves as a syringe for your recoat material. To fill up the syringe, point the lever downward (i.e., toward the recoat bottle), then spin the knurled dispensing screw counterclockwise until it spins easily to fill up the syringe (shown in the picture to the right). Then, to inject the recoat materials into the mold, point the lever horizontally (i.e., dealing with the knurled screw) and rotate the attach clockwise till close to the finish from the journey range is reached. Avoid bottoming the dispenser since this kqkbws harm the internal plunger; also be careful when re-interesting the threads in order to avoid go across threading the dispensing attach. A number of fill/inject steps may be required till air is displaced in the system. Use lens cells and an acetone or alcoholic beverages cleaning solution to collect any extra recoat materials that flows from your mold.

Yarn Binder – Just Posted..

We are using cookies on our website

Please confirm, if you accept our tracking cookies. You can also decline the tracking, so you can continue to visit our website without any data sent to third party services.