Do you require a pressure regulator or a flow regulator? All high-pressure regulators are created to accept incoming pressure of 150bar from the cylinder. This makes them a high-pressure regulator. But what do you require on the outlet of the regulator. Exactly what does your instrument/analyser/GC require? Pressure or flow?

beer regulator parts

Usually, a gasoline recognition tool will require stream (.5l/min) when a gas analyser may need stress at 1 or 2 bar. The instrument, analyser or GC will dictate what exactly is required.

Once this can be decided then we can continue.

Step Two: What is the outlet flow price or pressure requirement?

Particular flow rates or demands may be needed for a certain instrument or analyser.

Determining that degree will permit us to decide on a regulator with all the correct electric outlet requirements or even a adjustable range which include the value needed.

Flow: Many regulators have particular flow rates which are repaired, while some have a wide range of flow prices. A continuous flow regulator can provide the desired stream price required by the instrument. In cases where the analyser posseses an inner water pump then an on-demand stream regulator will provide the stream when a vacuum is put on the regulator.

(For more information read our blog on Very best Practice for Gasoline Recognition Instruments with Internal Pumps)

Pressure: All pressure regulators have electric outlet can vary such as -1.5bar, -3.5bar or -10bar. Choose the range which suits your requirement. If your analyser demands 2 bar then choose the -3.5bar range.

Step Three: Gas type and focus: The gasoline mixture or gasoline type will determine the content necessity of the regulator. Additionally it is essential when picking other materials such as tubes.

(For more information read our blog Selecting Suitable Materials for Calibrating Gas Recognition Equipment.)

Extremely corrosive fumes such as chlorine, ammonia, nitrogen dioxide, hydrogen cyanide need stainless-steel regulators.

Hydrogen sulphide and sulphur dioxide can use nickel coated brass if the focus is listed below 50ppm. Higher concentrations of H2S and SO2 require stainless-steel.

Low corrosive gas mixtures including CO, Carbon dioxide, O2 and a lot hydrocarbons would need brass. It is crucial never to use nickel coated brass for top levels of carbon monoxide, as CO and nickel are incompatible and can type tetracarbonylnickel.

In which high purity gas levels are employed with highly corrosive fumes, purging techniques are suggested.

Stage 4: What inlet connector would you require? Flow or Stress Regulators

The gasoline kind or gas mixture will determine what valve type is around the gasoline tube. Australian (AS), British (BS) or Northern American (CGA) specifications are typical based on where gas mixture was manufactured. The inlet connector on the regulator should match the gas tube valve. You must determine what sort of valve is in the tube, whether that is an old tube or a new cylinder. The material in the valve and regulator is going to be dependent upon the gasoline kind.

Inlet connections can be changed to match the gasoline mix if neccessary.

Stage 5: Do you demand a solitary or double stage regulator (pressure regulators only)

The electric outlet stress of any specialty gasoline regulator comes with an inverse relationship to the gasoline volume within the cylinder. Since the gasoline volume decreases the electric outlet pressure raises.

Can you demand a constant electric outlet stress throughout the usage of your analyser? Frequently analysis may take a moment to complete and so the analyser is left unattended.

In the event you demand a continuous pressure becoming shipped to your analyser then this dual stage regulator is necessary. The double stage regulator corrects for the increase in electric outlet stress and keeps pressure in the rczlsg device. According to step 2, in the event you need a 2 bar constant outlet pressure you will pick a double phase regulator with all the range -3.5bar and set the benefit to 2 bar.

If an increase in electric outlet pressure is irrelevant then this solitary stage regulator could be right for your application. Within the case of any -3.5bar range regulator the greatest outlet stress would be 3.5bar.

Solitary and dual stage regulators are accessible for all sorts of materials of pressure regulators.

Co2 Cylinder Regulator – Discover More..

We are using cookies on our website

Please confirm, if you accept our tracking cookies. You can also decline the tracking, so you can continue to visit our website without any data sent to third party services.